Basements & Waterproofing
The Secret to ArmorGuard Basement Coating is the advanced science behind our products. Other epoxy, paints and coatings, dry from the bottom up, causing hydration (water, air and metals airing outward), pushing out the new coating that has been applied causing pin holes to appear, and the new coating to delaminate, flake, peel or blister.This is why other products FAIL! Our basement coatings insulate your basement keeping your basement warmer and will never peel, flake or chalk!
ArmorGuard Coatings dry from the top down eliminating pin holes and bonding to the surface permanently with a 14,000 psi chemical bond strength, unmatched by other coatings. ArmorGuard Coatings were developed as a permanent solution to many different waterproofing problems such as; seawalls, dams, tanks, pools and basements and have been proven and field tested.
ArmorGuard® contains NO toxic organic compounds or heavy metals and is easily roller applied. No special equipment is needed. Our product applies at approx 15 mils per coat; unlike other interior coatings that apply at 2-5 mils at best.
ArmorGuard® is an industrial waterproof protective coating which is a 100% solid thermosetting epoxy made from soybeans, beans and peanuts, with titanium and flex enhancers added, for better durability and flexibility.
Benefits
- Odorless & Non-Toxic
- NO Pumps NEEDED!
- NO Drains NEEDED!
- NO VOCS
- 100% waterproof
- Easy 1 Coat Application
- Prevents Radon
"Armorguard chemically cures from the top down etching its way into the surface sealing pores, this is why primer is not required. "
To Pump...or not to Pump?
ArmorGuard® Basement coatings were designed after our pool and tank coatings and are HURRICANE AND FLOOD TESTED! As a matter in fact ArmorGuard is commonly used to correct problems with pump and drain systems, pumps and drain systems only redirect the water to a low point in the basement (a pit) then pumps are used to pump water from these pits to an outside area. What happens to the pump when you lose power? What happens when there is more water than the pump can handle? ANSWER - THEY FAIL!
Wearing A Raincoat...
As far as interior basement sealers/coatings go, most sealers or coatings are made to resist water, not to waterproof, read the label on the buckets. Other sealers/coatings have a high odor requiring you to move out. Rubber membrane coatings not only smell and remain tacky but also out gas leaving you with a potentially dangerous environment. Water based coatings break down with water, why would someone waterproof their basement with a product that breaks down with water? You can wear a rain coat, but if it has a hole or wears out overtime, you are going to get WET.
Our Coatings are Easy to Use... Satisfaction Guaranteed!
Take advantage of our Free Shipping Limited Time Offer!
Our Basement Products
ArmorGuard Color Topcoat Kit
ArmorGuard, the "Natural Choice" Epoxy Coating is easily roller applied. No special equipment is needed.
ArmorGuard is chemical, stain resistant and will seal water out permanently, not redirect water to another area
Priced affordably at:
1.5 Gallon Kit $237.00 (coverage 150-175 s.f, includes .5lb of ArmorGuard Cleaner and a 1.5 gal. unit of color top coating)
3 Gallon Kit $377.00 (coverage 300-350 s.f, includes 1lb of ArmorGuard Cleaner and a 3 gal. unit of color top coating)
ArmorGuard Trowel Mix
Fiber Reinforced Polymer Trowel Mix that is 10 times stronger than concrete and will permanently repair cracks, holes or degraded areas, our trowel mix is also used to set tile permanently.
1.5 Gallon Kit - $232.00
3 Gallon Kit - $387.00
Completed Basement Projects
Permanent Waterproofing
Time to get rid of that old water pump!
Save Time & Money
ArmorGuard Coatings were developed as a permanent solution.
Increased Value
ArmorGuard Coatings are not water-based! Keep moisture out permanently!
